Clip for hair with peony and buds of fabric
For the manufacture of this flower we take materials: - dense fabric of synthetic fibers of red color. - silk fabric green shade. - soldering iron with a fine tip. - a piece of ceramic tile. - needle with thread. - medium size hair clip. - small iron ruler. - a small piece of thin wire. - glue gun. - foil. - slightly corrugated paper of green color. - cardboard. - scissors. - candle.
In the beginning of work draw patterns for our composition. Petals in the form of a droplet cut from the bottom. Large will be 5.5 x 4.5 cm in size and 4.5 x 4.5 cm in size. Still need a small droplet 3 x 2 cm, a rectangle of 26 x 8 cm in size, two kinds of leaves. The billet is larger consists of 3 leaves, joined together, measuring 10 x 8 cm,and in a small template there will be 2 sheets fastened together and its size is 8 x 6 cm.
Getting Started I will open on a red fabric. We will work with a soldering iron on a ceramic tile. We start with a rectangle measuring 26 x 8 cm. Then we place it with the long side horizontally and with the help of an iron ruler we cut vertical stripes 0.6 cm wide inside this blank. Without reaching the edge at the top and bottom of 0.5 cm.
Then, using templates made of cardboard, cut out the same peony petals from the same fabric. Larger will be 12 pieces, and smaller blanks in the amount of 22 blanks.
Now we take silk green fabric and cut out one large and two small blanks according to the leaf pattern. And already in the finished leaves, in addition, in any form, in the wide part, we cut holes.
Next from we cut the same fabric across the width of the iron ruler strip,which are divided into 5 cm long.
From these strips we make triangles, cutting them diagonally. And then in each triangle the lower wide side is folded, fixing also with a soldering iron.
Light a candle, take it red petals and give them a new shape with the help of fire. Gray the edge of the petal and on small workpieces add a little accordion with a little finger scrolling, and in large workpieces we twist the tube inside.
For the pion assembly we take a cut rectangle, petals of 12 pieces of two sizes and 3 green leaves.
Let's start with bol xoy preform. We fold the rectangle in half to get an uncut fringe, and at the junction with a needle and thread, we make small stitches. Then, this blank is a little bit tight. Now take the glue gun and fasten this workpiece, twisting it in a circle. The middle of the peony has turned out.
Take small petals and paste them to the resulting middle in a circle in two rows 6 pieces.
After that came time for large petals. They are also glued in two rows.
Continue your work by sticking several green triangles, placing the flower upside down.
Left over 3 large sheets of this should be glued.
Peony is ready.But there are two more buds in our composition.
For them a pattern of a small droplet of green silk is cut out also with a soldering iron 10 blanks and we twist their edges over fire.
now begin assembling a long bud. We take 5 small petals, 5 green new blanks, a foil ball 10 x 10 cm.
Foil fix it on a piece of thin wire, glue the densely red petals.
And then we attach 5 green petals, positioning them in a circle.
We attach 3 small triangles to the base of the bud, and glue the wire with a strip of corrugated paper. But we still need one bud without wire.
Now we take a hair clip and fasten these flower buds onto it, position the short one without the wire at the beginning, and make a long bend at 90 degrees and fasten it to the first closer, place the remaining piece of wire along the clip. But from the seamy side, we definitely make an additional binding of silk.
Then we glue the peony next to the buds, making additional attachment to the base.
The decoration is ready.
Good luck to all.
Date: 09.10.2018, 08:41 / Views: 55473
Halloween drawings and applicationsSprig of MagnoliaMaking PlasticineRefinement ChargerHow to eliminate the beating of the cartridge in a screwdriverAir glass partition - 20 examples for your inspiration